🌏
AeroGCS KEA User Manual
  • AeroGCS KEA 2.3
  • 1 Getting Started
  • 2 Dashboard
  • 3 Home Menu
  • 4 Project
    • 4.1 Create Project
    • 4.2 Setting Location
    • 4.3 Flight Type
    • 4.4 Add a New Plan
    • 4.5 Use of an Existing Plan
    • 4.6 Edit the Plan
    • 4.7 Save Project
    • 4.8 Delete the Project
  • 5 Connecting a Drone
  • 6 RPA Configuration
    • 6.1 Selection of Airframes
    • 6.2 Calibration of Sensors
    • 6.3 Safety Parameters
    • 6.4 Assigning Flight Modes
    • 6.5 RC Calibration
    • 6.6 Motor and ESC Calibration
    • 6.7 Managing a Battery (Power Settings)
    • 6.8 Serial Parameter Settings
    • 6.9 Camera and Camera Config
    • 6.10 Joystick Settings
    • 6.11 Spraying Configuration
    • 6.12 Reset Parameters
    • 6.13 Advanced Settings
    • 6.14 Firmware Upgrade
      • 6.14.1 Automatic Firmware Upgrade
      • 6.14.2 Manual Firmware Upgrade
  • 7 Flight Types
    • 7.1 Waypoint Planning
    • 7.2 Survey Planning
    • 7.3 KML Survey
    • 7.4 Plan for Spraying
    • 7.5 Vertical Flight Plan
    • 7.6 Import KML
    • 7.7 Corridor Plan
    • 7.8 KML Spraying
    • 7.9 Circular Plan
    • 7.10 Read from Device
    • 7.11 Adding Rally Points
    • 7.12 Providing Fence
    • 7.13 Flight Fly View
  • 8 First Flight
  • 9 Flight Logs
  • 10 Team Access Management
  • 11 VTOL Support
    • 11.1 Survey Plan for VTOL
    • 11.2 VTOL Flight Modes
  • 12 Special Features
  • 13 Vehicle Type
  • 14. Hardware Supported by AeroGCS
  • AeroGCS KEA Enterprise
    • 1. Dashboard
    • 2. Creating a Project
    • 3. Managing a Team
    • 4. Drone Lease
    • 5. GREEN-E
      • 5.1 Revenue
      • 5.2 Crops
      • 5.3 Customers
      • 5.4 Acreage
      • 5.5 Seasons2
      • 5.6 Growth Statistics
      • 5.7 Revenue Trend
    • 6. Project Sync
    • 7. Live Tracking of Flight
    • 8. Settings
    • 9. LiveStream
    • 10. Incident Report
Powered by GitBook
On this page

Was this helpful?

  1. 6 RPA Configuration

6.8 Serial Parameter Settings

Previous6.7 Managing a Battery (Power Settings)Next6.9 Camera and Camera Config

Last updated 2 years ago

Was this helpful?

This section allows to you configure serial interface-related parameters.

For establishing the communication the selection of a proper serial port with proper baud rate and protocol is necessary. Therefore, here in this section, the user has to set the appropriate values of the baud rate and communication protocol.

Configuration options are as below.

  • Serial 0: Set baud rate and communication protocol for a console.

  • Serial 1: Set baud rate and protocol for Telemetry 1.

  • Serial 2: Set baud rate and protocol for Telemetry 2.

  • Serial 3: Set baud rate and protocol for GPS.

  • Serial 4: Set baud rate and protocol for serial 4.

  • Serial 5: Set baud rate and protocol for serial 5.

  • Serial 6: Set baud rate and protocol for serial 6.

  • Baud rate : Set the speed of transfer of bits from the serial port.

  • Protocol : Set the protocol of transfer of data.

  • Select the proper values of the baud rate from the dropdown menu.

  • Select the proper communication protocol from the dropdown menu provided.

  • After selecting all the parameters update the data by clicking on the "Update" button.

  • All the parameters are sent to the device to store and respond accordingly.

RPA Configuration -Serial Param
RPA Configuration -Serial Param